Fall 2017 Class Schedule (SCC)



Back to Previous Page

ENGR 300    Introduction to Engineering    1 Unit

Prerequisite: None.
Course Transferable to UC/CSU
Hours: 18 hours LEC
Description: This course provides an introduction to the different engineering disciplines and careers, the role of the engineer in society, the engineering approach to problem solving, the design process, and engineering ethics. The development of effective communication and study skills required of engineers is emphasized. This course is required of most engineering majors.

Schedule: Full Term, Aug 19-Dec 14
F         12:00PM-01:05PM LEC M.Taheri             SCC MAIN LUC 122         17023 
Textbook
On-Campus


ENGR 312    Engineering Graphics    3 Units

Prerequisite: MATH 335 with a grade of "C" or better
Advisory: It is expected that the student has experience and knowledge of the use of a personal computer.
Course Transferable to UC/CSU
Hours: 36 hours LEC ; 72 hours LAB
Description: This course provides fundamental training in the use of hand-drawing instruments and Computer Aided Design/Drafting (CADD) software to analyze, interpret, and solve engineering problems. Topics covered include elements of drafting, descriptive geometry, multi-view drawing, design process, and solution of engineering problems, culminating in a design project.

Schedule: Full Term, Aug 19-Dec 14
TTh       02:30PM-03:20PM LEC M.Taheri             SCC MAIN LUC 122           
TTh       03:30PM-05:35PM LAB M.Taheri             SCC MAIN BUS 104         17222 
Textbook
On-Campus


ENGR 400    Introduction to Electrical Circuits and Devices    3 Units

Prerequisite: PHYS 420 with a grade of "C" or better
Corequisite: MATH 420
Course Transferable to UC/CSU
Hours: 54 hours LEC
Description: This course provides the engineering student with the basic fundamentals of DC and sinusoidal electrical circuit theory and analysis. The following circuit elements are covered: resistors, capacitors, inductors, independent sources, and dependent sources. Topics that are covered include circuit analysis techniques, sinusoidal analysis, phasors, Thevenin and Norton equivalence, natural and step response of first-and second-order circuits, three-phase analysis, complex power, and operational amplifiers. (C-ID ENGR 260)

Schedule: Full Term, Aug 19-Dec 14
MW        10:30AM-11:50AM LEC L.Li                 SCC MAIN LUC 122         16569 
Textbook
On-Campus


ENGR 405    Engineering Problem Solving    3 Units

Prerequisite: MATH 401 with a grade of "C" or better or concurrent enrollment in MATH 401.
Advisory: It is expected that the student has experience and knowledge in the use of a personal computer.
Course Transferable to UC/CSU
Hours: 36 hours LEC ; 54 hours LAB
Description: This course provides an introduction to the use of computers in solving engineering problems using MATLAB. Students will learn to use basic programming techniques including program control, relational and logical operators, selection scripting, and file management while implementing computational solutions.

Schedule: Full Term, Aug 19-Dec 14
TTh       07:30AM-08:20AM LEC K.Awni               SCC MAIN BUS 153C        19496 
Textbook
TTh       08:30AM-09:50AM LAB K.Awni               SCC MAIN BUS 153C          
On-Campus


ENGR 412    Properties of Materials    4 Units

Prerequisite: CHEM 400 and PHYS 410 with grades of "C" or better
Course Transferable to UC/CSU
Hours: 54 hours LEC ; 54 hours LAB
Description: This course covers atomic and crystal structures and mechanical, electrical, and magnetic properties of engineering materials. Also covered are steady and non-steady state diffusion, phase diagram analysis, heat treatment of metals, and corrosion. Laboratory exercises cover both destructive and non-destructive testing of materials.

Schedule: Full Term, Aug 19-Dec 14
MW        01:00PM-02:20PM LEC L.Li                 SCC MAIN LUC 122           
M         02:30PM-05:35PM LAB L.Li                 SCC MAIN LUC 123         17288 
Textbook
T         10:30AM-01:35PM LAB L.Li                 SCC MAIN LUC 123         17523 Textbook
Please select one Laboratory from the two Labs listed above and register using that class number. You will be automatically enrolled into the Lecture.
On-Campus


ENGR 422    Engineering Mechanics, Statics    3 Units

Prerequisite: MATH 401 and PHYS 410 with grades of "C" or better
Advisory: Completion of a drafting course prior to enrolling in this course will facilitate the analysis of statics problems.
Course Transferable to UC/CSU
Hours: 54 hours LEC
Description: This is the first course in engineering mechanics. Topics in this course include two and three dimensional force system analysis using vector techniques, moments and couples in two and three dimensions, centroids and moment of inertia, friction, forces in beams, and truss analysis. This course is required for Mechanical, Civil, Aeronautical engineering transfer students and by some electrical engineering programs. Contact an engineering instructor and/or the transfer center for specific transfer institution requirements. (C-ID ENGR 130)

Schedule: Full Term, Aug 19-Dec 14
MW        08:45AM-10:05AM LEC K.Awni               SCC MAIN LUC 122         16574 
Textbook
On-Campus

Fall 2017 Class Schedule

Updated: December 7, 2017